สวัสดีปีใหม่ 2560Adjusting PWM Frequencies For further knowledge on Arduino PWM frequencies refer to the ATMega Complete Datasheet and this Arduino.cc page "Secrets of Arduino PWM" http://arduino.cc/en/Tutorial/SecretsOfArduinoPWM Regarding Arduino Mega This article is not fully compatible to Arduino Mega (or ATmega2560 microprocessor) For Arduino Mega: (tested on Arduino Mega 2560) timer 0 (controls pin 13, 4) timer 1 (controls pin 12, 11) timer 2 (controls pin 10, 9) timer 3 (controls pin 5, 3, 2) timer 4 (controls pin 8, 7, 6) TCCRnB, where 'n' is the number for the timer. TCCR2B for timer 2, TCCR3B for timer 3. Eg: TCCR2B = TCCR2B & 0b11111000 | 0x01; //sets Arduino Mega's pin 10 and 9 to frequency 31250. //code typically inserted in setup() Thanks to valerio_sperati (http://arduino.cc/forum/index.php/topic,72092.0.html) How to adjust Arduino PWM frequencies by macegr in this forum post http://forum.arduino.cc/index.php?topic=16612#msg121031 Pins 5 and 6: controlled by Timer 0 in fast PWM mode (cycle length = 256) Setting Divisor Frequency 0x01 1 62500 0x02 8 7812.5 0x03 64 976.5625 <--DEFAULT 0x04 256 244.140625 0x05 1024 61.03515625 TCCR0B = (TCCR0B & 0b11111000) | ; Pins 9 and 10: controlled by timer 1 in phase-correct PWM mode (cycle length = 510) Setting Divisor Frequency 0x01 1 31372.55 0x02 8 3921.16 0x03 64 490.20 <--DEFAULT 0x04 256 122.55 0x05 1024 30.64 TCCR1B = (TCCR1B & 0b11111000) | ; Pins 11 and 3: controlled by timer 2 in phase-correct PWM mode (cycle length = 510) Setting Divisor Frequency 0x01 1 31372.55 0x02 8 3921.16 0x03 32 980.39 0x04 64 490.20 <--DEFAULT 0x05 128 245.10 0x06 256 122.55 0x07 1024 30.64 TCCR2B = (TCCR2B & 0b11111000) | ; All frequencies are in Hz and assume a 16000000 Hz system clock. Issues from adjusting PWM frequencies and workarounds: from koyaanisqatsi in this forum post http://forum.arduino.cc/index.php?topic=16612.msg121040#msg121040 If you change TCCR0B, it affects millis() and delay(). They will count time faster or slower than normal if you change the TCCR0B settings. Below is the adjustment factor to maintain consistent behavior of these functions: Default: delay(1000) or 1000 millis() ~ 1 second 0x01: delay(64000) or 64000 millis() ~ 1 second 0x02: delay(8000) or 8000 millis() ~ 1 second 0x03: is the default 0x04: delay(250) or 250 millis() ~ 1 second 0x05: delay(62) or 62 millis() ~ 1 second (Or 63 if you need to round up. The number is actually 62.5) Also, the default settings for the other timers are: TCCR1B: 0x03 TCCR2B: 0x04 Any thought on the Arduino Mega? PWM frequencies on Timer 0, pins 5 and 6, Arduino Uno by yanngg, 02-15-2012 Timer 0 uses a prescale factor which is set to 64 by default To set the prescale factor use this line in the setup function Setting Prescale_factor TCCR0B = _BV(CS00); 1 TCCR0B = _BV(CS01); 8 TCCR0B = _BV(CS00) | _BV(CS01); 64 TCCR0B = _BV(CS02); 256 TCCR0B = _BV(CS00) | _BV(CS02); 1024 To use Fast PWM on Timer 0 Write this line in the setup function TCCR0A = _BV(COM0A1) | _BV(COM0B1) | _BV(WGM01) | _BV(WGM00); And to calculate the PWM frequency, use Fast_PWM_frequency = (16 000 000)/(Prescale_factor*256); To use Phase-correct PWM on Timer 0 (half the frequency of Fast PWM) Write this line in the setup function TCCR0A = _BV(COM0A1) | _BV(COM0B1) | _BV(WGM00); And to calculate the PWM frequency, use Phase_correct_PWM_frequency = (16 000 000)/(Prescale_factor*510); Changing the prescale factor on Timer0 will affect functions millis(), micros(), delay(),... To adjust millis(), micros(), delay(),... accordingly, You can modify a line in the wiring.c function in the Arduino program files hardware\arduino\cores\arduino\wiring.c In the beginning of wiring.c you can find: // the prescaler is set so that timer0 ticks every 64 clock cycles, and the // the overflow handler is called every 256 ticks. #define MICROSECONDS_PER_TIMER0_OVERFLOW (clockCyclesToMicroseconds(64 * 256)) You need to modify the prescale factor in this function to the corresponding line For fast PWM (default): #define MICROSECONDS_PER_TIMER0_OVERFLOW (clockCyclesToMicroseconds(PRESCALE_FACTOR* 256)) For phase-correct PWM : #define MICROSECONDS_PER_TIMER0_OVERFLOW (clockCyclesToMicroseconds(PRESCALE_FACTOR * 510)) Example: DC motor drive on the Arduino UNO, pins 5 and 6 For Fast PWM of 62.500 kHz (prescale factor of 1) Use these two lines in the setup function: TCCR0A = _BV(COM0A1) | _BV(COM0B1) | _BV(WGM01) | _BV(WGM00); TCCR0B = _BV(CS00); And modify the line in the wiring.c function in the Arduino program files hardware\arduino\cores\arduino\wiring.c : #define MICROSECONDS_PER_TIMER0_OVERFLOW (clockCyclesToMicroseconds(1 * 256)) For Phase-correct PWM of 31.250 kHz (prescale factor of 1) Use these two lines in the setup function: TCCR0A = _BV(COM0A1) | _BV(COM0B1) | _BV(WGM00); TCCR0B = _BV(CS00); And modify the line in the wiring.c function in the Arduino program files hardware\arduino\cores\arduino\wiring.c : #define MICROSECONDS_PER_TIMER0_OVERFLOW (clockCyclesToMicroseconds(1 * 510))